Results 1 to 10 of 14

Hybrid View

  1. #1
    Members bsfman's Avatar
    Join Date
    Mar 2011
    Location
    Cape Coral, FL
    Posts
    355

    Making a vegetable mold

    While surfing the web, I discovered a picture of square watermelons being grown in Japan and the watermelons were being sold for big bucks! Further Googling turned up a page showing how to build a watermelon mold box out of plexiglass. This started me thinking about molding other fruit and vegetables into various shapes.

    I Googled vegetable molds and found a number of sites (including eBay) selling cucumber molds. The price for a set of three molds was very high - like $88 bucks not including shipping! That's a LOT of money to mold just three cucumbers! It got me thinking about making my own cucumber molds out of plexiglass.

    I decided to start simple and just make square cucumber molds to test the concept. Further Googling on the topic of thermoforming plexiglass gave me enough knowledge to take a stab at it. I bought a thin sheet of 18" X 24" plexiglass at Home Depot for just under 10 bucks. I used a hand held reciprocating saw to slice it into small sheets...



    then peeled off the backing on both sides and wound up with this...



    My idea was to heat the plexiglass in the kitchen oven to soften it, them use 1" angle iron as a jig to form a V shape.



    Two pieces formed this way complete the mold.

    Through trial and error, I found that 5 minutes at 350 degrees softens the plexiglass to the point where it can be shaped. I used a sheet of aluminum foil tp support the plexiglass on the oven grate.



    I laid the soft plexiglass on the bottom piece of angle iron and used the smaller piece of angle iron to sandwich the plexi between the iron as I pressed down firmly and held until the plastic set. This worked pretty good and formed a nice, clean V shape, but the flat flanges of the mold wanted to warp so I used potholders to try to keep them flat and smooth until the plastic set. It only takes a minute or two for the plexiglass to cool sufficiently to set.

    I used a small drill bit (3/32nds) to drill pilot holes in the flange, then used a 1/4" bit to expand them. (Light pressure on the drill is required or the plexiglass will crack.) I used 1/2 inch long 1/4" bolts and nuts to fasten the two halves of the mold together. The finished mold looks like this...



    Soon, I had cranked out a number of square molds. Hey! If you're gonna mold cukes, you may as well do more than one at a time, right?



    To use the mold, I just found small cucumbers (about chapstick sized) and slid them into the mold. A few days growth and you have this...







    Having proven the concept, I embarked on making a heart shaped mold (I figure heart shaped pickles will be a big hit come Valentine's Day!) Building a heart shaped mold turned out to be much more difficult. I finally succeeded at it, but that will be the topic of a separate post. I'm currently working on a tetrahedral tomato mold too - also a separate topic post to follow!

  2. #2
    Junior Member
    Join Date
    Jan 2021
    Posts
    1
    where did you get the heater strip?

Similar Threads

  1. Mold on media
    By jvision in forum Aquaponics Knowhow
    Replies: 9
    Last Post: 01-10-2015, 08:33 AM
  2. Used vegetable oil OK for fish?
    By germanbull in forum Back Yard Systems
    Replies: 2
    Last Post: 03-17-2012, 06:09 PM
  3. Replies: 3
    Last Post: 07-09-2011, 10:01 PM
  4. Making water changes a bit easier . . .
    By Riverside in forum Want To Know HOW TO..?
    Replies: 8
    Last Post: 06-24-2010, 02:14 PM
  5. Making Lemonade
    By badflash in forum SUMP
    Replies: 3
    Last Post: 05-16-2010, 06:11 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •